Special Offer5% OFF on All Services for New Clients Only!Claim Offer →
Hicksville, NY • Nassau County • 10.3 miles west of Deer Park

Furnace Repair in Hicksville, NY

Last updated Reviewed by Waseem Shahzad, Lead Technician

Hicksville is 10.3 miles west of our shop at 60 S 2nd St, Unit V in Deer Park. Our vans head out on the Long Island Expressway to Exit 41S, or take the Southern State Parkway when traffic is better, then come into town on Route 107 or Route 106. Housecall Pro shows K2 on Hicksville furnace calls from December 2014 through November 2026.

Most of those calls started the same way: a cold house and a furnace that would not light or would not stay lit. Below is what we actually found and replaced, followed by what each failure means for a Hicksville homeowner. Call (631) 414-7141 any hour. K2 answers 24/7.

What furnace repairs has K2 done in Hicksville?

Our Hicksville furnace records cover about a dozen years. They include a control board, flame sensor, igniter and rollout switch replaced in November 2026, a limit switch and ignitor on a furnace we installed in 2017, a hot surface ignitor in 2014, and blower motor work in February 2026. Here is each visit in plain terms.

  • November 2026 (Waseem): a no-heat call. The control board had failed, and the furnace also needed a new flame sensor, igniter and rollout switch.
  • November 2025, same home: control board and flame sensor replaced, with a filter change.
  • December 2022, same home: transformer, flame sensor and inducer issues. This home has more than one furnace unit.
  • November 2022: a follow-up to a fall tune-up. We replaced the flame sensor and changed two Aprilaire HEPA filters.
  • December 2017 to April 2018: a home where K2 installed the furnace in September 2017. Over that winter we replaced a limit switch and an ignitor and sorted out a thermostat issue.
  • December 2014: the hot surface ignitor was checked and replaced, and the limits and safeties were checked.
  • February 2026 (Waseem): a heating system issue at another Hicksville home that involved blower motor work.

What does a furnace control board do, and why replace other parts with it?

The control board is the furnace's brain. It takes the call for heat from the thermostat, starts the inducer, powers the igniter, opens the gas valve, watches the flame sensor and then runs the blower. When it fails, the furnace may do nothing at all, or it may start the sequence and stop partway through.

A new board will not fix a worn igniter or a coated flame sensor, so we test the whole chain before leaving. That is why the November 2026 Hicksville visit ended with a board, flame sensor, igniter and rollout switch rather than a board alone. If your furnace clicks and hums but never lights, our guide on a pilot or ignitor that won't light walks through what you can safely look at first.

What is a rollout switch, and is it safe to reset one?

A rollout switch sits near the burners and opens if flame or heat spills out of the burner area instead of going up the flue. When it trips, the furnace shuts down. It is a safety device, so a tripped rollout switch means something pushed heat where it should not go, and that cause needs finding.

Common reasons include a blocked flue or vent, a weak inducer, or a heat exchanger problem. Some rollout switches have a reset button, but pressing it over and over without knowing why it tripped is a bad idea. In November 2026 we replaced a worn rollout switch on a Hicksville furnace along with its board, flame sensor and igniter. If yours trips again after one reset, leave it off and call us.

Why does the flame sensor keep coming up on Hicksville furnace calls?

A flame sensor is a thin metal rod that proves the burners are lit. Over a few heating seasons it builds up a coating that weakens the signal. The furnace then lights, runs for a few seconds and shuts the gas off because it cannot confirm a flame. After a few tries it locks out and the house cools.

The flame sensor shows up in four of our Hicksville records: November 2022, December 2022, November 2025 and November 2026. Cleaning buys time; a sensor that is pitted or cracked gets replaced. Waseem's tip: if the furnace lights and quits after a few seconds, count how many times it tries before it gives up and tell us when you call. Swap in a clean filter while you wait.

Does a house with two furnaces need anything different?

Each furnace has its own control board, flame sensor, igniter, filter and thermostat, so each one can fail on its own schedule. A problem on one unit leaves part of the house cold while the rest stays warm. Both units should be serviced on the same visit so neither one gets skipped.

One Hicksville home in our records has more than one furnace, and it has needed a transformer, flame sensors, inducer attention and two control boards between 2022 and 2026. Many Hicksville Capes and split levels from the late 1940s and 1950s have been expanded over the years, and a second unit is one way owners heat the added space. Label each thermostat and filter slot so you know which furnace serves which rooms.

What makes a limit switch trip, and what can you do about it?

The high-limit switch shuts the burners off when the furnace gets too hot inside. That nearly always traces back to airflow: a clogged filter, closed or blocked registers, a weak blower or ductwork that is too small. The burners cool, relight and overheat again, so the furnace short-cycles and rooms stay lukewarm.

On the furnace we installed in September 2017, we replaced a limit switch that winter, along with an ignitor, and corrected a thermostat issue. In a compact Hicksville ranch or Cape, a couple of closed bedroom registers or furniture over a return can cut airflow more than people expect. Our post on a furnace that turns on and off every few minutes explains the pattern.

Why would a furnace run but push out little or cold air?

If you hear the furnace running but the vents barely move air, the blower is the first suspect. A failing blower motor or its capacitor can spin slowly or not at all. Then the heat stays inside the furnace, the limit switch trips and the burners shut down while the house gets colder.

In February 2026 Waseem handled blower motor work on a heating system at a Hicksville home. Before you call, check that the thermostat fan is on Auto, the filter is clean and the furnace door is closed tight, since many furnaces will not run with the door switch open. If those all check out, the blower needs a technician.

How does K2 serve Hicksville, and will a furnace job need a permit?

Our technicians cover all of Hicksville, from the blocks near the LIRR station and the Broadway corridor to the streets around Cantiague Park, off Old Country Road and near Hicksville High School on Division Avenue. We answer 24/7 and give you an arrival window when you call. Most furnace repairs never involve the town.

Some jobs need a permit from the Town of Oyster Bay Department of Planning and Development (74 Audrey Avenue, Oyster Bay, NY 11771); we'll tell you up front if yours does. For more, see our furnace repair service, the Hicksville HVAC hub, boiler repair in Hicksville and our no-heat emergency page.

Furnace Repair in Hicksville: Questions

What should I check before calling about a furnace with no heat?

Make sure the thermostat is set to Heat and above room temperature, the batteries are fresh, the furnace power switch is on, the breaker has not tripped and the filter is not clogged. Also check that the furnace door is seated. If all of that looks right, call (631) 414-7141.

How often should I change my furnace filter?

Look at it monthly during the heating season and replace it when it looks gray or clogged. Thicker media filters, like the Aprilaire filters we changed at a Hicksville home in November 2022, last longer between changes, but they still need replacing on schedule.

Can K2 repair a furnace that another company installed?

Yes. Who installed it does not change the work. We test the control board, ignition, flame sensor, safeties and blower on any gas furnace and explain what we find before we replace anything.

Does a fall tune-up stop all no-heat calls?

No, but it catches a lot of them early. A tune-up is where weak flame sensors and worn igniters get spotted. Our November 2022 Hicksville visit was a follow-up to a fall tune-up, and the flame sensor was replaced then rather than on a cold night.

Is a furnace that lights and then shuts off dangerous?

Usually it is the furnace protecting itself, often because of a dirty flame sensor or a tripped limit switch. It is not something to keep restarting. If you smell gas, leave the house, call National Grid from outside and then call us.

Request Furnace Repair in Hicksville

Or call (631) 414-7141.

I agree to the privacy policy. By submitting this form and signing up for texts, you consent to receive text messages from K2 Mechanical at the number provided, including messages sent by auto dialer. Consent is not a condition of purchase. Msg & data rates may apply. Msg frequency varies. Unsubscribe at any time by replying STOP or clicking the unsubscribe link (where available) and no further messages will be sent. Reply HELP for help.
Call (631) 414-7141